Wooden balau Deck Built in Umkomaas – KZN South Coast

This wooden deck built in Umkomaas on the South Coast of Kwa-Zulu Natal turned into a very nice job with many extras and a happy client who paid timeously. What a pleasure.

We removed and dumped an existing pine deck that had started to show signs of failure in the deck boards themselves. The structure was still ok as it had been built using H3 CCA Treated pine which is suitable for outdoors for a minimum of 50 years as per www.sawpa.co.za. It was the deck boards that had started to rot at the screw hole due to water sitting in the screw hole for long periods of time. It is very important to firstly close that screw hole at the time of building the deck and then to maintain them going forward to stop any water getting into the screw hole. Water will travel very quickly along the end grain of wood and this screw hole provides an ideal point of entry for water. They are simply filled with a clear epoxy mixed with saw dust to match the colour and then sanded flat before sealing or oiling the deck.

Once we had a clear slate we built a new deck using balau deck boards. We changed the design a few times as we built to accommodate the clients requirements. We tried to create a deck that would flow nicely from one level to the other. The top deck was built flush with the house and then we built steps at a 45 degree angle to gain access to the lower deck around the pool which extended along the front of the lower level sliding doors.

We included a curved front on the upper deck to break the straight lines and then clad that fascia as it was very visible when driving up the driveway. We normally include two deck boards as a fascia to the front edge of a deck to hide the structure below and finish it off neatly. In this instance we added four deck boards on the curve because the driveway is a lot lower then the deck and when driving up the driveway the underside of the deck was the first thing you see when entering the property. The client may still need to add planters with some plants in to completely cover that structure but the 4 deck boards give it a nice broad fascia which hides a lot of the structure.

The stairs were challenging. Originally they were to be curved risers and treads which would have meant either cutting deck boards at an angle and laying them straight or trying to bend the deck boards. The risers would have been easy enough by bending a deck board around the arc, but the treads would have been a bit more difficult because it would have meant bending the board through its width (not thickness). The centre of the circle, was off set to the corner of the deck or the top of the stairs and the centre of the circle occurred in the pool. So all in all not an easy task. Because the arc itself was quite gentle you would not have really noticed that it was curved so we opted for a straight edge to our risers and treads. Much easier and less problems going forward with deck boards trying to return to their original straight position. Often less is more.

For a free no obligation quote on your wooden deck, pergola, stairs and other timber works please call us on 082 496 5444 or use the contact us form below.

Wooden Pool Deck Built in Kloof, Durban

This wooden deck was a simple pool deck that we built in Kloof, Durban. The pool had originally been built at an angle to the house which limited the available space between the house and pool. The client wanted to create a wooden deck that was parallel to the house so that he could maximise the space between the edge of the pool and the house.

As result we needed to build part of the wooden deck over the pool and the trick was to support it sufficiently over about a 3.5m span so that it didn’t bounce or sag. We couldn’t of course put supports or posts into the pool so we increased the size of the beam running over the pool to a 50 x 152. We still had to trim the 152 down to about 140 as we needed to install this beam on top of the existing pool coping, on both sides, and we were limited by how high we could come up from that surface. In these instances one starts “stealing space”. A term we use at The Wood Joint for gaining every available millimetre possible in order to maximise structural strength.

We then clad the downpipes and support posts of the existing awning with deck boards to create two fairly large wooden posts and hide the PVC downpipes. This gave the effect of large wooden posts holding up the awning. The flower boxes were also clad to match the theme.

A small ledge of about 200mm wide was added along the wall running up to the pizza oven at bar height of about 1.2m from ground. A small cupboard was built in the recess that the builder had left on the right hand side of the braai in which glasses and other braai, or bar, utensils can be stored.

Stainless steel hinges were used aluminium knobs were fitted. We used a normal latch system on the inside so that when you close it, it locates behind, and out of sight. We included a single shelf for glasses. We tucked the deck underneath the braai area so that wood and charcoal can be stored there.

This deck was sanded and sealed with an oil based sealer. An oil based sealer is far superior to a water based sealer or mineral based sealer that dries on the surface. Oil cannot peel and flake. It simply disappears with exposure to UV so there is no need to sand the deck in the future.

We are available to quote on your decking needs. Please call us on 082 496 5444 or use the contact form below.