Balau pool deck and walkway – Kloof, Durban

This slideshow requires JavaScript.

We engaged with Masslandscapes, a landscaper and garden designer (082 468 3759) on this balau pool deck project in Kloof, Durban to provide a solution for the client who wanted an area alongside their pool that they could utilise more. Before the project started there was the standard paved area of about 1m alongside the pool which was bordered by grass of about 1m and then a flower bed, before dropping down a small bank to the rest of the garden. The client wanted to increase the size of usable area alongside the pool.

Initial designs were to have a very similar layout as per the pics above with a semi-circle sort of node protruding over the bank to gain height and create a look out area overlooking the Kloof Gorge. This proved to be out of budget and would probably have resulted in doubling up sitting area as there was already a large tiled verandah extending out from the living area doors. The final design was settled on which is what you see in the pics.

We needed to excavate some of the garden down and move this top soil for use in another area of the garden. It is always recommended that sufficient space be left below the deck and below the bottom of the lower most bearer or joist to allow enough air flow to dissipate and evaporate any water that settles below the deck. Too often I have seen deck boards rotting prematurely due to insufficient space being left below. Water gets trapped below and the underside of the deck and structure remains damp. I normally recommend at least 150mm below the lowest point of the structure. Once we had enough space below we installed our structure using H3 CCA treated pine. Please see here for an article on the use of CCA Treated pine as structures for decks and balau as deck boards. All cut ends of treated pine, as a matter of course, are re treated with an approved end sealer. When a CCA treated piece of pine is cut it exposes a section that is not treated and can accelerate rot.

Post to ground are set in concrete and installed at the correct distance on the bearers to stop any bounce in the bearer and to provide enough support to prevent the bearer breaking. There are guidelines supplied by engineers for distances that these supports need to be installed. These posts need to be H4 CCA treated pine as they are in constant contact with wet soil.

A lot of this job involved lining up existing paving, pool copings, patio etc. to the deck so the lines were seamless and everything ties in neatly. A walkway, as can be seen from the pics, was created to run alongside the existing raised patio for access to the rest of the garden.

In finishing our decks we fill the screw holes with a clear epoxy mixed with saw dust to match the colour as closely as possible and then grind and sand it flat. Standard wood filler doesn’t quite do the trick and fails with exposure to weather. The filling of screw holes is a very important aspect of deck building. It prevents water sitting in the counter sunk screw hole which would then travel up the end grain of the balau and cause early rotting of the balau deck boards. We use a clear epoxy so that we can match the colour to the deck boards. Off the shelf epoxies are either grey or white in colour and don’t take the saw dust that well to match the colour. Also these epoxies dry very hard. It is better to use an epoxy that is semi pliable when dry. Through seasons of dry and wet, hot and cold, the inside diameter of the counter sunk screw hole will vary ever so slightly. If the epoxy has dried too hard it will cause it to pop out leaving a weak spot on the balau deck board. During maintenance intervals these should be checked and replaced if they have in fact popped.

The deck was oiled using a zero wax content product. The beauty of oil is that it soaks into the wood and therefore cannot peel and flake. A peeling deck is an expensive deck to maintain because you would need to sand off the coating completely to avoid a patchy finish when re-applying the coating. Whereas an oil simply degrades due to exposure to UV over time. A pressure wash and re-oil is all you need to do at maintenance intervals which is relatively inexpensive and easy to do as opposed to sanding the deck again. The oil also allows the natural beauty of the wood to shine through resulting in a more natural wood looking product. Coatings give them the effect of a painted deck especially over time when layer after layer has been applied.

For a free no obligation quote on your timber balau decking, walkways, pergolas and other outdoor timber products, please call us on 082 496 5444 or use the contact us form below. We operate throughout KZN.

Cheap Wooden Deck Builders in Durban

This slideshow requires JavaScript.

I was prompted to write this article on cheap wooden deck builders in Durban for various reasons and to highlight some of the dangers of using the cheapest wooden deck builder that you can find. Being South African we all should know the Afrikaans saying “goedkoop is deurkoop”. Or loosely translated to English “you get what you pay for”. There is no exception in the wooden deck building industry.

One should consider that in order to offer a certain level of service a wooden deck builder needs to charge a certain rate. If that rate is relatively low, in comparison to other quotes, then certain sacrifices need to be made either in terms of the quality of materials that are used, the time it takes to do the job to save on labour costs, the quality of labour used to perform the task or the end profit to the contractor. Or a combination of the above. It also makes sense that it will never ONLY be the profit that is sacrificed when rates are lowered. It will be a combination of all of the components, probably skewed away from profit. On the other hand if rates are extremely high the quality of materials and labour can only reach a maximum level (i.e. the best) and any extra money becomes mere profit to the company.

Reliability of contractors using vehicles that may break down should also be taken into account. If margins are small there is often not enough profit to do the maintenance on vehicles, plant or tools that is required and down time can occur that delays the job being completed on time, or at all. Small labour forces may also be used that are often shared amongst several jobs, again resulting in down time and delays in project deadlines. Furthermore unskilled labour forces may be used directly affecting the quality of workmanship and the life span of the end product.

Of equal concern is the tendency of a contractor to use sub standard materials to save on cost wherever possible. In the wooden deck building industry there are various standards of materials. For instance you get red and yellow balau. Red is cheaper but is inferior and will not last as long. Screws can either be Kalgard decking screws with a life span of 25 years or the normal screws one can buy from the hardware with a life span outdoors of approximately 5 years. It is only in 5 years time that you may realise you have made a costly mistake by choosing the cheapest contractor. Or by pushing prices down to a point where a contractor who normally performs a quality job is forced to cut costs and use sub standard materials.

I am often asked to provide a discounted rate. I have no problem offering better rates based on volume as volume enables me to do the job more efficiently. I have done my costings properly and through a combination of accurate calculations and experience have found a point at which I need to set my rates in order to be able to afford quality materials, skilled reliable labour and maintenance of vehicles, plant and tools in order to build a wooden deck the best way it can be built.

We don’t drive the latest Ford Rangers at The Wood Joint. We run a fleet of 4 vehicles ranging from 10-year-old Isuzus with over 400, 000kms on the clock, serviced and maintained regularly so that they are reliable to newer similar vehicles. As such our rates have been set in order to provide the correct materials, skilled reliable labour and reliable vehicles.

I have a list of sub contractors that I can provide you with who will do the job cheaper than me. I can provide a list of suppliers who will supply cheaper materials. I can also show you a list of jobs where third-party sub contractors have taken short cuts in their pursuit of money due to low rates and jobs that have had the wrong materials used and are now prematurely failing.

At The Wood Joint we use only the correct materials, our own permanently employed crews of skilled deck builders each with his own set of tools and reliable vehicles to get them to work on time. We do not, any longer, use third-party subcontractors. We’ve learnt the hard way. Hopefully we can save you the expensive learning process too through this article. We are not the cheapest, we are not the most expensive either, we are correctly priced to offer the standards of quality and service that you expect.

To read more on balau and it’s characteristics please Balau Sundecks

For a free no obligation quote on wooden decking, pergolas, screens, cladding, pergolas and balustrades please call us on 082 496 5444 or use the contact us form below.

Wooden Balau Decking Companies in Durban

This slideshow requires JavaScript.

 

Here’s a wooden deck we at The Wood Joint built in Durban recently. The Wood Joint is a wooden decking company situated in Durban and servicing most of KZN. It was a low-level wooden deck basically at ground level joining the pool to the patio and semi surrounds. The site was situated in la Lucia Durban.

When building a wooden deck that will join a verandah to a pool, one needs to be careful to set the height of the pool correctly. The height to the verandah is of course pretty much set based on what the threshold of the sliding doors are. So working from a datum line of the top of the tiles of the verandah one would set the top of the concrete ring beam of the pool down 70mm from the required height of the deck. This will allow for a substructure of 50mm and a deck board thickness of 20mm (19mm in fact but to keep things simple rounded to 20mm). A 50mm batten fixed to the top of the concrete ring beam of the pool will give sufficient space to allow water to evaporate properly, keeping below the deck as dry as possible, and enough structure to create a positive fixing of deck board to bearer. The distance created between top of deck and pool should be minimal. It is not advisable to go much higher than 70mm because it creates a very big “climb” out the pool (from water level to top of deck).

In this deck pictured you will see we ran the deck boards perpendicular to the verandah and pool side. Using this method it is not that important if the side of the pool is parallel to the verandah as the length of the deck boards can be varied quite easily without noticing any difference in length. On the other hand when the deck boards are run parallel to the pool side and verandah one needs to be careful to get the two as perfectly parallel as possible. Any difference will be visible because a deck board will need to be cut in a wedge shape to complete the space. If the difference is not that great then one can “fan” the deck boards to take up the difference in space by making one end’s gaps slightly bigger than the other end. So on one end a 6mm gap can be left and on the other a 4mm gap (normally 5mm throughout). This gains 1mm per deck board run. After 20 deck boards one can adjust for a 20mm difference in spacing. Another “trick” when running boards parallel to the pool side and verandah is to try to end on a full board rather than a half board. Again space between boards can be adjusted either up or down to try to end on a full board. It is much neater and won’t cause as many problems going forward. From the pics you’ll see we ended the deck on a half board which in this case was unavoidable because of the configuration of paving and deck.

You’ll see from the pics that the garden is mostly left for landscaping until after the deck has been built. Trying to build a deck with newly laid grass and not damaging it is near impossible. Always get you building work done before landscaping.

For a free no obligation quote on your decking requirements in Durban please call us on 082 496 5444 or use the contact us form below.

Engineered Hardwood Flooring

This slideshow requires JavaScript.

Hardwood flooring has become ever popular in many countries. In South Africa, home owners are opting for these in preference to the old style parquet and the laminated style of flooring. Hardwood floors go hand-in-hand with luxury, and offer timeless beauty and are low on maintenance. Home owners looking for a classic look might like to consider engineered hardwood flooring. These points should be taken into account, or kept in mind when weighing up the pros and cons of hardwood flooring.

Unlike conventional hardwood, which comes from its raw state and into your home, engineered hardwood is a more complex product which consists of layers. The outermost appearance layer is a hardwood veneer, a thin slice of wood of whatever wood type you prefer. The inner layers are made of plywood, high density fiberboard, or hardwood. These core layers give the product more stability than regular hardwood, while the outer veneer surface gives the floor its aesthetics, its beauty, and, of course, its authenticity.

Engineered hardwood is different to a hardwood laminated ‘wood’ because the surface is made of real wood. While laminated flooring has a core of high density fiberboard, its surface is basically a picture of wood. Laminate is less expensive than engineered and solid hardwood, but has a different look, feel and even sound when walking on it, due to its make up.

Pros:

  • Engineered hardwood flooring is designed to reduce moisture associated with conventional hardwood.
  • The layers block moisture and provide added stability to your floor.
  • This is a low maintenance option because of the fact that Engineered Flooring will not swell or warp.
  • Choosing engineered flooring is considered more environmentally-friendly than traditional hardwood for various reasons.
  • Veneer is sliced very carefully and precisely – it is not cut with a saw. This process produces no sawdust, which means that the entire tree can be used. The sawdust which we know amounts to a significant pile when making hardwood boards is wasted wood.
  • Hardwood trees grow a lot more slowly than the trees used to construct engineered flooring cores. More surface area is produced making veneer, therefore installing traditional hardwood uses many times the amount of slow-growing tree. This makes the replenishing time much longer.

Engineered Hardwood Flooring Cons

  • There are very few disadvantages to this type of hardwood flooring but it is neither a foolproof project and not necessarily the right floor for every application.

Comparable to solid hardwood in terms of cost: –

Engineered floors are still considerably more expensive than laminated floors, tile or carpet. They are, however much more hardy, are low maintenance and will wear a lot better.

That said, one should also take into account the biggest concern as a homeowner … that being avoiding shoddy or inferior engineered work and products, merely because of cost.

Veneers that are too thin will prevent sanding and refinishing opportunities that may double the lifetime of the floor.

Some veneers are so thin and poorly made that they can prematurely warp or fade.

Core layers should still be made from high-quality wood. Some manufacturers try to cut corners by using fiberboard or oriented strand board which might well compromise the stability of your floor and could result in an inferior flooring product.

Your Home is your Castle … quality surpasses cutting corners

It is, without exception, easier to install engineered flooring and the handy man homeowner is often encouraged to install his or her own engineered floors. It is never-the-less, a major project with big financial implications, therefore, I suggest you weigh up carefully, the virtue of employing an experienced craftsman to do the job (who will also guarantee his finished product, surely?) and doing the work yourself …and without wanting to reduce your skill-ability, don’t be too over zealous about your own home improvement skills just to get the job done cheaper! Even for the majority of homeowners who hire a flooring contractor for the job, you’ll save a hefty sum on installation, which is important given that most engineered flooring is more expensive than solid wood.

The cost of high-quality engineered floors (thick veneers) will depend on various issues, the obvious one being the type of wood you choose. In South Africa, imported Indonesian Balau is readily available, is solid, a hard wood and also hard-wearing, able to withstand much more than a softer local wood might be. It lands at quite a reasonable price and is of a superior quality. It is, for example largely used for outdoor decking. Solid wood flooring may be cheaper overall, however it will still take longer to install.

For a free no obligation quote on your solid hardwood engineered flooring please contact us on 082 496 5444 or use the contact us form below.

Wooden Balau Pergola Built in Plantations – Durban

This wooden balau pergola was built at Plantations in August 2016. We had custom-made galvanised steel base plates made up in order to secure the uprights to the existing paving. Because the uprights had to be installed on the edge of the paving we couldn’t dig and bury the post so we installed them into these base plates which were then fixed to the paving using sleeve anchors.

When designing a base plate for this application it is important to make the tube that will carry the upright post long enough in order to give it lateral support to stop the structure “racking”. Also the actual base must be big enough to be sturdy, but small enough so as to still be neat and not get in the way. We used a 90 x 90mm balau upright. The back row of uprights were fixed to the outside of the wall surrounding the entertainment area.

On the top we installed 30 x 102 as purlins which were spaced at 600 centres. I’ve found that spacing a 30 x 102 at 600mm centres works best from a structural point of view and a cost point of view. Obviously the closer the purlins are spaced the more expensive the pergola will be and one must be careful not to space them too far apart as it affects the stability of the structure and the visual appearance.

On top of that we installed 30 x 40 balau battens running perpendicular to the purlins at 120mm centres resulting in a gap between battens of 90mm being 3 times that of the batten itself. This works well in order to give enough broken shade without creating a completely closed effect on top. It also helps on the pocket by using 30 x 40 as opposed to 30 x 60mm.

Because of the existing chimney on one side of the area we had to cut purlins beams and battens in order to finish it neatly around this chimney whilst still making sure that all ends were fixed. If the ends are left unsecured they tend to twist over time.

These balau pergolas can be left un-oiled or oiled. If left un-oiled then they will eventually turn a silvery grey colour. If oiled they will remain slightly darker. It is not advisable to coat them with any other product other than an oil as it will eventually peel and flake and maintenance then becomes difficult and expensive. They can be pressure washed to remove dirt and grime that settles over time.

For a quote on your wooden balau pergolas, deck, walkways, balustrades, stairs and other timber works, please contact us on 082 496 5444 or use the contact us form below.

Balau Timber Pool Deck, La Lucia, Durban

Here’s a wooden pool deck we built in La Lucia, Durban recently. In the gallery above you can see pics of the old deck and then pics of the new deck. The old wooden pool deck had started to rot at critical points. The reason for rot in many wooden decks is that the screw holes are not plugged, water gets in and travels up the end grain of the wood resulting in rot at the screw holes. Water travels more easily along the end grain of wood than the side or face grain. So it is important to seal the end grain as far as possible to prevent this. In the case of the end of deck boards the water never really gets trapped so it can drain away quickly enough to prevent rot. However in the case of a screw holes water collects in the screw hole and then has enough time to be absorbed by the end grain before it evaporates. As a standard procedure we fill counter sunk screw holes with epoxy to prevent this from happening.

The epoxy we use is clear so that saw dust can be mixed with it to match the colour as closely as possible. It is also slightly pliable. In hot and cold weather, wood expands and contracts, as does most materials. If you consider a screw hole. The sides of the screw hole will expand thereby closing the screw hole or making it smaller. Whatever is in the screw hole, as a plug, will also expand. So if the screw hole is getting smaller and the plug is getting bigger it makes sense that whatever is in there will likely try to “pop” out. Using a slightly pliable epoxy can reduce the chance of this plug popping out. Hence the reason for not using solid wood plugs cut with a plug cutter. The epoxy should be pliable enough to take up the expansion of the screw hole but hard enough not to degrade due to weather conditions.

We used 90mm balau deck boards on this deck. They are slightly more expensive but some clients prefer them to the standard 68mm boards. Being a wider board one needs to secure them on both shoulders on each joist rather than just a single screw in the middle of the boards, as is the case with a 68mm board.

The job took a bit longer than I would have liked because the substrate that we were building on top of, paving and concrete in this case, were quite uneven so we had to shim and trim joists to get the top of our joists level, flat and at the desired height to be flush with the inside of the house. The jacuzzi cladding was also quite tricky because we had to build a removable structure so that one can access the front of and below the jacuzzi. One side of the jacuzzi step is also wider than the other one so the corner required some fancy carpentry work in order to get the boards to line up and match. I’m glad I took so many pics of the deck before we removed it so that we could copy it exactly.

There were also some wedges that we had to cut along the front edge as the tiles and existing patio were not square to the wall we were building our wooden deck up against. Whenever the existing buildings are not square there is always some sacrifice one needs to make and the trick is to get it least visible to the eye. In this case the client wanted the wedges rather than cutting the tiles or bringing the front of the deck past the line of existing buildings.

For a free no obligation quote on your wooden pool deck, or other balau timber construction, please call us on 082 496 5444, or use the contact form below and one of our representatives will get in touch with you.

Wooden deck in Massaranduba, Hillcrest, Durban

This deck was built with Massaranduba. Although Massaranduba is about 30% more per square metre than balau the client insisted on it as it is a much harder and denser wood than balau. As such it will last longer. It has a slight reddish tinge to it. This deck is to be left unsealed so will eventually turn grey / sliver. Therefore one will not notice that is massaranduba, but it will last longer. When choosing between balau or massaranduba one needs to weigh up the difference in cost vs. the longevity of both timbers. There is nothing wrong with balau, it will also give you a long life span. Massa is of a better quality and will therefore outlast balau.

We decked around the pool flush with the tiling on the patio which resulted in a single 90mm deck board being used as a fascia on the inside of the pool. Hence the difference in height between the water level and the deck is not that great. Often the deck can come up too high resulting in a big step up to the deck from water level. The pool therefore needs to be set at the correct height, in relation to the patio, to accommodate the deck at the correct height.

A quick note on new pool decks. The hardwood typically used in decking contains tannins which leach out when it rains. Storing them on a tiled surface almost always results in stains being left on the tiles after a downpour. Likewise one needs to be careful of installing the fascia on the inside of the pool, or deck boards that are installed on the pool’s edge, prior to filling the pool with water. If there is no water in the pool and it rains, these tannins will leach out and run down the new marbelite pool surface, staining it. The only way to get rid of the stains successfully is to sand it off. It is advisable therefore to get the pool done and filled before decking up to the sides of the pool and installing the fascia board. Alternatively, don’t marbelite until these tannins have completely leached out. It’s a tricky one because the pool contractor doesn’t want to marbelite until the lawn is done because of dust. The landscaper normally comes last, so it’s a bit of juggling that is required.

We decked around a circular concrete slab which is to be a fire pit and up to the edge of the brick and plaster bench around the fire pit.

We also installed a small pergola above the sliding door and included a small bar counter that can be accessed from both sides of the patio and deck. There was also a small decked area at the back of the house next to the fish pond and a screen on the front of the house.

For the screen we used a 20 x 30 slat instead of a normal 19 x 68 deck board. Although a 19 x 68 deck board works well as a screen, a narrower piece (30mm) with a smaller gap is a bit different and not the run of the mill timber screening. Although it is slightly more expensive than a normal 68mm wide deck board screen, it is very effective.

All in all a very nice job to work on and a pleasure to work with Massaranduba. It is lovely stuff. Hard as nails and long-lasting.

For a free no obligation quote on your wooden decking, pergola or screening needs in Durban or Cape Town, please call us on 082 496 5444 or use the contact us form below.

Wooden Deck Built in Hillcrest, Durban

Here’s video of a wooden deck we built recently in Hillcrest, Durban showing the different stages of the build.

Give us a call for a quote on your wooden sun deck, wooden pergolas, walkways, bridges, floors or fences on 082 496 5444 or use the contact us form below.

 

Wooden Sun Decks and Wire Rope Balustrades

Wooden Balau Deck with Wire Rope BalustradeWooden deck with wire rope balustradeWooden deck with wire rope balustradeA wire rope balustrade on a wooden sun deck, as pictured in this article, has a few pros and cons to it which I will discuss below. I will also describe the method used to install wire rope balustrades and what to be careful of to ensure that the job runs smoothly. If you don’t feel like doing it yourself, or don’t have the right tools or time, then scroll to the bottom and complete the contact us form below. I will contact you and we can take the task off your hands. Alternatively call us on 082 496 5444. We are Durban based.

Firstly one should choose the correct wire rope to use. We use the 4mm marine grade stainless steel wire rope with button heads. One can also get the 5mm wire rope but I have found that that often contains one rogue strand which will tarnish over time and spoil the look of your balustrade. The 4mm wire rope does not bend as easily as the others so where you get to a 90° bend you will need to terminate your wire rope with a button head and start again on the next run. The 4mm wire rope can bend around gentler curves quite easily. It is just the 90° bends that require a new run.

We start by installing our wooden, normally balau, uprights and these can be anything from a 30 x 60, 40 x 60 or 60 x 60. Obviously the 60 x 60 is better as it is more solid and stable, but it unavoidably carries a higher price tag. A 40 x 60 works very well, but the 30 x 60 can do the job just as well if installed properly. Now install your capping on the top to hold the whole lot together while you install your wire rope.

There are various methods of securing your wire rope. We use the button heads as opposed to turnbuckles. A hole is drilled, to a diameter slightly bigger than the button head, in the wooden upright and the wire rope is threaded through it so that the tag end is protruding to the outside of the balustrade. One side of the button head is then inserted over the wire rope and crimped using a special crimping tool. The crimping tool looks very similar to a large bolt cutter with a head that has been adapted to accept the button head and crimp it to the right size to hold the wire rope without damaging it.

Now cut a length of wire rope to slightly more than is required. Remember think twice, cut once as it is always easier to cut more off then to add more on once it has been cut too short. Now all your holes need to be drilled in all the other upright posts. Measure you spaces out accurately so that your wire rope will run parallel to the capping on the top and the wooden deck on the bottom. When drilling through a piece of wood it is easy to hold the drill slightly skew resulting in the drill bit exiting the wood at an angle which will result in the exit hole not being in the place it should be. So drill half way from one side and then drill from the other side to get your entry and exit holes perfectly lined up. It doesn’t matter if the middle of your hole is slightly skew because you can’t see it and it is not enough to impede the path of the wire rope. Thread the other un crimped end of the wire rope through all your holes in your uprights until you get to the end.

Wooden deck with wire rope balustradeNow take the other button head with the thread on it and measure, very carefully, where you need to cut your wire rope. You will need to cut it with a thin cutting disk on a baby grinder so as to get a nice clean-cut. If you cut it too long you won’t be able to tension it and too short, well start again from the beginning. So cut and check before crimping the other end. The second button head will be inserted through the hole from the back and the wire rope inserted into it from the front and crimped. Make sure you have your thread to its longest position so that you still have thread to use to tension it. Now tension it, but do not over tighten it. It is not a guitar string and only needs to be tight enough to be visibly straight. Over tightening it will result in the end wooden uprights bowing, or even failing.

Pros of Wire Rope Balustrades

• Does not interfere in your vision when seated and looking through the balustrade
• Adds a second material, other than timber, for a clean minimalist look and feel
• Marine grade stainless will last a life time

Cons of Wire Rope Balustrades

• Does not offer as much protection from objects or people falling through the strands as timber does
• If installed incorrectly can look terrible
• Can detract from the timber look and feel

Good luck in installing your wire rope balustrade. I hope this article has helped. If you’re not up to it, please complete the form below, or contact us on 082 496 5444 and we will gladly quote you to do the task for you. We are Durban based and work throughout KZN.

Laying Balau Deck Boards Down

This video shows how we have laid these deck boards without ending on a half deck board or a wedge-shaped deck board.

Most often two opposite walls will not be exactly the same length and they certainly won’t be designed to accommodate an exact amount of deck boards with a uniform gap. What can happen is that you start on one end and end up with a half deck board that has to be ripped length ways on the other end. This is both unsightly and can result in premature failure because the deck board may become too narrow to be secured properly.

If the two opposite walls are not the same length then the problem is compounded because not only will you end up with half a deck board, but you will end up with half a wedge-shaped deck board.

So we need to try to mitigate this problem by adjusting our gaps between deck boards either up or down, very slightly so as to be unnoticeable.
Normally the gap between deck boards is 5mm and we commonly use a 6 inch nail as a spacer. By increasing one end of the line of deck boards to 4mm and the other end to 6mm you can effectively gain, or lose 2mm per line of deck boards. In this video these boards were 90mm wide, so if on every line we gain 2mm, we will gain about 20mm for every 1m of deck boards installed. So after 4.5m you can gain a full deck boards width. On most decks this is sufficient to allow you to finish on full deck boards and to avoid having to cut a wedge-shaped deck board.

Watch the video and you will see how I panned around the little alcove that we had to deck into. We employed both methods here to end on a full deck board and to avoid a wedge-shaped deck board.

It is far easier when decking to the end of the deck as here you can continue with full deck boards until you reach the end, and then cut your joists off at the right length.
It makes for a much neater deck and less chance of failure.
Other videos are also available on the Videos Tab on the menu bar on the left. These show other techniques we employ in building wooden decks which can make the job a lot easier.

For a free no obligation quote on your wooden deck, please contact us on 082 496 5444, or use the contact us form below.